| HPBCANADA.COM http://www.hpbc.ca/ |
|
| 1993 Johnson 225 http://www.hpbc.ca/viewtopic.php?f=19&t=3026 |
Page 1 of 1 |
| Author: | Pantherman [ August 22nd, 2015, 10:26 pm ] |
| Post subject: | 1993 Johnson 225 |
Hi there... I have a 1993 225 johnson looper v6... I just bought this motor a month and half ago and installed a week ago... Motor was rebuilt and has 50 hrs .... The starbourd side is over heating and i have changed out the Head gasket .. 2 thermosts.. heat sensor.. water pump is new .. Checked hose blow off valve joining 2 thermosts and alls working... Flushed power head with hose for 15 mins ... Motor has lots of presure and temps are running hot.. Port side is running normal operating temp... If any OMC Runners on here have any ideas what else i could check for id appreciate it... Thanks |
|
| Author: | Matt [ August 23rd, 2015, 8:11 am ] |
| Post subject: | Re: 1993 Johnson 225 |
Hi Patherman, I'm not sure if anyone here will know or not. Probably? Anyway, on Facebook there are 2 groups that definitely have a ton of knowledge and can probably help: Strictly OMC https://www.facebook.com/groups/874113192613275/ Evinrude and Johnson Outboard Power https://www.facebook.com/groups/55593643398/ |
|
| Author: | beavertonae-21 [ August 23rd, 2015, 11:21 am ] |
| Post subject: | Re: 1993 Johnson 225 |
Frank Jackson on here, or racer( Al Stoker) or Instigater ( Gary) on screamandfly.com. |
|
| Author: | Pantherman [ September 1st, 2015, 5:18 pm ] |
| Post subject: | Re: 1993 Johnson 225 |
Thanks for the reply back on helping regaurding problems with over heating on my 225.. Big thanks too Mark Nowak .. Strictly OMC ... Evinrude Johnsons Outbourds.. Alot of hrs put in trouble shooting and turning out the Adaptor plate was restricted on starbourd side from when power head was rebuilt teck drop remains of base gasket in port draining holes... Motor is up and running temps are great.. Thanks again Mark and fellow helpers guiding me through this... Safe boating everyone. |
|
| Author: | wildcatt [ September 2nd, 2015, 8:26 am ] |
| Post subject: | Re: 1993 Johnson 225 |
Pantherman wrote: Thanks for the reply back on helping regaurding problems with over heating on my 225.. Big thanks too Mark Nowak .. Strictly OMC ... Evinrude Johnsons Outbourds.. Alot of hrs put in trouble shooting and turning out the Adaptor plate was restricted on starbourd side from when power head was rebuilt teck drop remains of base gasket in port draining holes... Motor is up and running temps are great.. Thanks again Mark and fellow helpers guiding me through this... Safe boating everyone. Glad you got it going. That was an odd problem to diagnose - for sure. Kudos to those that helped figure that one out. Good luck! |
|
| Author: | phillnjack [ October 6th, 2015, 8:21 am ] |
| Post subject: | Re: 1993 Johnson 225 |
its great when someone just knows what is wrong straight away. you can be pulling your hair out due to not having a clue, especially after tracing everything you know that could cause the problem. But when a good guru tells you then it just seems so simple. This is wheethe internet and forums really do come into play, in the old days of NO internet, problems could go on for months, and even cause people to scrap a perfectly good engine . glad you got it going good now, and don't forget to buy that fella a pint if or when you see him. also great advice on who to get intouch with !! |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| © 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com | |