It is currently October 31st, 2024, 7:01 pm

nitro gearcase

View active topics

All times are UTC - 5 hours [ DST ]


Post new topic Reply to topic  [ 6 posts ] 
Author Message
 PostPosted: July 8th, 2014, 4:00 pm   
Member

Joined: July 8th, 2014, 12:47 pm
Posts: 35
Location: SASKATOON Saskatchewan
Hey guys I have a nitro gearcase for 15 inch mid. 4 spline shaft. Was rebuilt and put away for a while. Has been completely stripped and is in zinc chromate primer right now. The unit is not the swept back style but the straight skeg style. This came off of a 75-76 stinger. Unit is ready for paint and to be bolted on and go. Also have 79 evinrude 75 hp short shaft with club foot that could be put together as a package. Open to offers.


Top
 Profile Send private message  
 PostPosted: July 11th, 2014, 9:51 am   
Member

Joined: August 22nd, 2013, 4:13 pm
Posts: 273
:) What are you asking? The straight skeg is not what we use in T-7560/850 due to boat spin out in turns. So we will have to cut off skeg and weld on swept back skeg. With that in mind, give us a figure to contemplate. We will be in Dinville the weekend of 8/16 &17 for a race. Perhaps you could deliver it to us at Dunville.

Thanks Thom
216-314-7025 cell
330-425-4266 wk


Top
 Profile Send private message  
 PostPosted: July 11th, 2014, 12:20 pm   
Member

Joined: July 8th, 2014, 12:47 pm
Posts: 35
Location: SASKATOON Saskatchewan
I have 850 tied up in the case and I have an empty swept back style nitro case as well. Id like to see a grand. I am in Saskatchewan but for you guys I would gladly package this unit and ship it out to you anyway you would like. I was going to run this lower on a 14.5 foot race tunnel but decided to run a speedmaster. I would expect shipping times to be 3-4 days max being as it is in canada.

Michael Brown.
306-231-0546
Michaelbrown.pilot@gmail.com


Top
 Profile Send private message  
 PostPosted: July 11th, 2014, 2:07 pm   
Member

Joined: August 22nd, 2013, 4:13 pm
Posts: 273
Hi Michael,


Thank you for the reply, but without insulting you, we can purchase an entire 49.7 cid Stinger motor for 1000-1200.00. I'm afraid we must pass. We had much less in mind. We would entertain a lower offer if you wish.

Thank you,

Thom Bucknell
330-425-4266 wk
216-314-7025 cell


Top
 Profile Send private message  
 PostPosted: July 11th, 2014, 2:28 pm   
Member

Joined: July 8th, 2014, 12:47 pm
Posts: 35
Location: SASKATOON Saskatchewan
Thats ok im not insulted I paid lots for the unit. I dont have to sell the lowers just thought someone in the t boat world could use the lower. Again thank you for replying


Top
 Profile Send private message  
 PostPosted: August 18th, 2014, 6:50 pm   
Member

Joined: July 8th, 2014, 12:47 pm
Posts: 35
Location: SASKATOON Saskatchewan
Sold.


Top
 Profile Send private message  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Style originally created by Volize © 2003 • Redesigned SkyLine by MartectX © 2008 - 2010